RDF Dryer Manufacturer in the United Kingdom
See how we dry RDFLooking for RDF dryers manufacturers in the United Kingdom? STRONGA builds FlowDrya lines to order at its Hertfordshire works and supplies them to the United Kingdom — see the regulatory and economic context below.
We supply FlowDrya RDF drying plants to customers across Britain, engineered and built to order at the STRONGA works in Hertfordshire and delivered nationwide. RDF is one of the materials most shaped by British waste policy: rising Landfill Tax and constrained residual-waste capacity push shredded refuse toward cement kilns and energy-from-waste plants, both of which reward a drier, higher-calorific feed. We are candid that we do not yet have a documented RDF drying reference on British soil; the FlowDrya platform, however, is proven here through our sawmill, anaerobic-digestion and woodchip installations in England and Wales, and every RDF machine ships with full commissioning, operator training and a hot test before handover.
Supplying the United Kingdom
We supply the United Kingdom from our Hertfordshire works — we have no documented RDF installation in the United Kingdom yet. Our FlowDrya projects in the United Kingdom to date cover other materials:
Regulatory context
Operating a plant that stores, treats or dries a waste-derived or organic material normally requires an environmental permit from the Environment Agency (or the devolved regulator in Scotland, Wales and Northern Ireland); the operator must demonstrate technical competence and comply with the permit conditions.
Source: https://www.gov.uk/guidance/waste-environmental-permits · checked 2026-08
Exporting waste-derived fuel such as RDF or SRF abroad is controlled under the assimilated Waste Shipments Regulation: most movements to recovery in the EU require prior written notification and consent from all competent authorities (amber-list controls), and the export of domestically derived RDF to non-OECD countries is prohibited.
Source: https://www.gov.uk/guidance/importing-and-exporting-waste · checked 2026-08
Solid recovered fuel produced from non-hazardous waste is specified and classified under EN ISO 21640, which assigns classes on net calorific value, chlorine content and mercury content so the fuel can be traded and burned consistently in cement and lime kilns.
Source: https://www.iso.org/standard/71309.html · checked 2026-08
Applicable standards: EN ISO 21640, EN ISO 17225-4, PAS 110, PAS 100.
Economic context
Landfill Tax on the disposal of most active waste in England and Northern Ireland is £130.75 per tonne from 1 April 2026 (the lower rate for inert waste is £8.65 per tonne); Scotland and Wales apply aligned devolved rates. The escalating tax is the primary economic driver for diverting material away from landfill.
Source: https://www.gov.uk/government/publications/rates-and-allowances-landfill-tax/landfill-tax-rates-from-1-april-2013 · checked 2026-08
The median UK gate fee for non-hazardous landfill, excluding Landfill Tax, was £34 per tonne in WRAP's UK Gate Fees Report 2025-26, and median energy-from-waste gate fees rose again across all categories surveyed.
Source: https://www.wrap.ngo/resources/report/uk-gate-fees-report-2025-26 · checked 2026-08
UK manufacturers paid an average of 17.08 pence per kWh for electricity and 3.71 pence per kWh for gas in Quarter 2 2025 (DESNZ Quarterly Energy Prices, September 2025). High industrial electricity prices reward drying equipment that runs on recovered waste heat and minimal electrical power rather than direct electric heating.
Source: https://assets.publishing.service.gov.uk/media/68da5e91dadf7616351e4b5e/quarterly-energy-prices-september-2025.pdf · checked 2026-08
Worked illustration (assumptions stated):
The domestic economics of drying RDF turn on avoided disposal and cheaper heat. With Landfill Tax at £130.75 per tonne from April and a median non-hazardous landfill gate fee near £34 per tonne on top, sending wet residual waste to hole-in-the-ground disposal is the costliest route by a wide margin. Drying lifts calorific value so each tonne substitutes more fossil fuel in a kiln, and because British industrial electricity averaged 17.08 pence per kWh against gas at 3.71 pence, a dryer that runs on recovered kiln heat and very little electrical power protects the margin. Assumptions: the figures are national medians and averages; your gate fee, heat source and offtake contract determine the actual payback.
Figures are indicative and were last reviewed August 2026; energy and disposal prices move — contact us for a current assessment.
RDF Dryer Manufacturer in the United Kingdom — FAQ
Do you supply RDF dryers in Britain?
We do. FlowDrya RDF dryers are manufactured to order in Hertfordshire and delivered throughout Great Britain and Northern Ireland, with installation typically completed on site within days and followed by commissioning and a full hot test.
Which regulations apply to RDF drying and movement here?
A site that stores or treats RDF normally needs an environmental permit from the Environment Agency, and any export of RDF for recovery abroad falls under waste-shipment notification controls, with movement of domestically derived RDF to non-OECD countries prohibited. Both drive demand for a stable, dried fuel that finds a compliant home.
Do you have a UK RDF installation yet?
Not for RDF specifically – we will not imply a reference we do not hold. Our nearest documented British projects dry bark, digestate fibre and woodchips, and they demonstrate the same PulseWave drying platform an RDF plant would use.
Which offtakes accept dried RDF?
Cement kilns and energy-from-waste plants are the usual homes, both preferring a lighter, higher-calorific, consistent feed that improves burner stability and thermal-substitution rates while cutting rejected loads.
How quickly is an RDF plant commissioned?
After factory testing, a delivered unit is normally installed within days and brought online through a structured sequence covering start-up, shutdown and a supervised trial run before handover.